Watlow EZ-ZONE PM Integrated Controller Manuel d'utilisateur Page 45
- Page / 181
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Watlow EZ-ZONE
®
PM Integrated Controller • 42 • Chapter 3 Keys and Displays
Chapter 3: Keys and Displays
3
Advance Key
‰
Advances through parameter
prompts.
Upper Display:
In the Home Page, displays the process
value, otherwise displays the value of
the parameter in the lower display.
Zone Display:
Indicates the controller zone.
1 to 9 = zones 1 to 9
A = zone 10 E = zone 14
b = zone 11 F = zone 15
C = zone 12 h = zone 16
d = zone 13
Lower Display:
Indicates the set point or output power
value during operation, or the param-
eter whose value appears in the upper
display.
EZ Key/s:
This key can be programmed to do
various tasks, such as starting a pro-
file.
Channel Display:
Indicates the channel for any given
EZ-ZONE module.
- Available with the PM4, 8 and 9
only.
Temperature Units:
Indicates whether the temperature
is displayed in Fahrenheit or Cel-
sius.
Percent Units:
Lights when the controller is dis-
playing values as a percentage or
when the open-loop set point is dis-
played.
Output Activity:
Number LEDs indicate activity of
outputs. A flashing light indicates
output activity.
Profile Activity:
Lights when a profile is running.
Flashes when a profile is paused.
®
1/16 (PM6) DIN
®
1/8 DIN (PM9) Horizontal
®
1/8 DIN (PM8) Vertical
®
Infinity Key ˆ
Press to back up one level, or
press and hold for two seconds to
return to the Home Page. From
the Home Page clears alarms and
errors if clearable.
Note:
If integrated limit, the Infin-
ity Key is labeled Reset
RESET
1/4 DIN (PM4)
Up and Down Keys ¿ ¯
In the Home Page, adjusts the set
point in the lower display. In other
pages, changes the upper dis-
play to a higher or lower value, or
changes a parameter selection.
Communications Activity
Flashes when another device is
communicating with this control-
ler.
Note:
Upon power up, the upper or left display will briefly indicate the firmware revision and the
lower or right display will show PM representing the model.
- User’s Guide 1
- Integrated Controller Models 1
- Safety Information 2
- Warranty 2
- Technical Assistance 2
- Table of Contents 4
- Table of Contents (cont.) 5
- Chapter 1: Overview 7
- DeviceNet 8
- TCP, and Profibus DP 8
- A Conceptual View of the PM 9
- Getting Started Quickly 10
- Functions 11
- Remote Set Point Operation 12
- Function 15
- Chapter 2: Install and Wire 19
- 1/16 DIN (PM6) 19
- 1/4 DIN (PM4) Dimensions 22
- Installation 23
- Chemical Compatibility 24
- Dig I/O 5 & 6 26
- 485 Comms 26
- PM Integrated Isolation Block 27
- Low Power 28
- High Power 28
- Digital Input 5 - 6 28
- Digital Input 7 - 12 29
- Input 1, 2 Thermocouple 29
- Input 1, 2 RTD 29
- Digital Output 7 - 12 32
- Internal Supply 33
- Output 1, 3 Universal Process 34
- Output 2, 4 Switched DC 35
- Quencharc Wiring Example 37
- Ethernet LED Indicators 38
- Activity Status 39
- Link Status 39
- Network Status 39
- Module Status 39
- DeviceNet™ Communications 40
- Profibus DP Communications 42
- EZ-ZONE ST 43
- 2. Double click on Ports 44
- 1/16 (PM6) DIN 45
- 1/8 DIN (PM9) Horizontal 45
- 1/8 DIN (PM8) Vertical 45
- 1/4 DIN (PM4) 45
- Attention Codes 46
- Chapter 4: Home Page 48
- Default Home Page Parameters 48
- Modifying the Home Page 49
- Custom Menu Parameter Options 49
- Modifying the Display Pairs 50
- Header Name Definition 51
- Communication Protocols 52
- Profibus DP 54
- Chapter 5: Operations Page 55
- Chapter 6: Setup Page 70
- Navigating the Setup Page 70
- On (63) 99
- Watlow EZ-ZONE 100
- Chapter 7: Profiling Page 106
- Navigating the Profiling Page 106
- Starting a Profile 107
- Profiling Parameters 109
- Chapter 8: Factory Page 116
- Navigating the Factory Page 116
- Chapter 9: Features 122
- Chapter 9: Features (cont.) 123
- Tuning the PID Parameters 126
- Manual Tuning (cont.) 127
- Autotuning with TRU-TUNE+ 127
- Before Tuning 127
- How to Autotune a Loop 127
- Calibration Offset 128
- Calibration 128
- Filter Time Constant 129
- Sensor Selection 130
- Sensor Backup 130
- Scale High and Scale Low 130
- Range High and Range Low 130
- Receiving a Remote Set Point 131
- Ten Point Linearization 131
- Retransmit 132
- Resetting a Tripped Limit 133
- Control Methods 134
- On-Off Control 135
- Proportional and (P) Control 135
- Dead Band 136
- Dead Band (cont.) 137
- Variable Time Base 137
- Variable Time Base (cont.) 138
- Single Set Point Ramping 138
- Cascade Control 138
- Compressor Control 138
- Input 1 Output 1 139
- Alarm Hysteresis 140
- Alarm Latching 140
- Alarm Silencing 140
- Alarm Blocking 140
- Current Sensing 141
- Open Loop Detection 141
- Programming the EZ Key/s 141
- CIP Implicit Assemblies 146
- Compact Assembly Class 146
- Software Configuration 147
- Searching Network for Devices 148
- Single Loop Control 151
- Example 3: Square Root 152
- Example 4: Ratio 152
- Example 5: Differential 153
- Example 6: Cascade 153
- Curve A (PID) 154
- Curve B (Cascade) 154
- Curve C (Single-control) 154
- Example 8: Vaisala 155
- Motorized Valve Control 156
- Chapter 11: Appendix 157
- CIP Implicit Assembly 163
- Compact Class 1 A through 7 A 165
- Compact Class 1 B through 7 B 166
- Specifications 171
- Dimensions 173
- [`oF;t] Minimum Off Time 94 176
- Series EZ-ZONE 180
- 3 Year Warranty 181
- CUSTOMER 181
- SATISFACTION 181
Produits connexes et manuels pour Capteurs Watlow EZ-ZONE PM Integrated Controller
(134 pages)
Capteurs Watlow EZ-ZONE RM Manuel d'utilisateur
(155 pages)
(155 pages)
Capteurs Watlow EZ-ZONE RMC Manuel d'utilisateur
(213 pages)
(213 pages)
Capteurs Watlow EZ-ZONE RMC Manuel d'utilisateur
(213 pages)
(213 pages)
Capteurs Watlow EZ-ZONE RMC Manuel d'utilisateur
(213 pages)
(213 pages)
Capteurs Watlow EZ-ZONE RMC Manuel d'utilisateur
(236 pages)
(236 pages)
Capteurs Watlow EZ-ZONE RME Manuel d'utilisateur
(112 pages)
(112 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels