Watlow EZwarePlus Programming Manuel d'utilisateur Page 5
- Page / 264
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EZwarePlus Programming Manual v
Table of Contents
COPYRIGHT NOTICE ....................................................... ii
WARRANTY .................................................................... ii
IF SERVICE IS REQUIRED ................................................ ii
APPLICATIONS ASSISTANCE ........................................... ii
Regarding Watlow Part Numbers .................................. iii
Table of Contents .......................................................... v
Chapter 1 – Introduction ................................................ 1
Welcome ....................................................................... 1
EZwarePlus Support ...................................................... 1
HMI Models Supported.............................................. 1
PLCs Supported .......................................................... 1
About Your Documentation .......................................... 1
Conventions ............................................................... 1
What You Need ............................................................. 2
OIT/HMI Basics .............................................................. 3
Projects ...................................................................... 3
Backing Up Projects ................................................... 3
Objects ....................................................................... 3
Graphics Object ......................................................... 4
Windows .................................................................... 4
What is an HMI5000P/L/HD Series? .............................. 4
List of Features .............................................................. 5
Chapter 2 – HMI Local Setup .......................................... 8
Factory Configuration .................................................... 8
Calibrating the Touchscreen ...................................... 8
Getting into Local Setup ............................................ 8
Changing the System Settings .................................... 9
Viewing System Information .................................... 14
Transferring Projects and Data from USB/SD Card .. 15
Changing or Restoring the HMI Settings by USB or SD 17
Chapter 3 – Connect the HMI to the PLC or Controller .. 19
Connecting to COM1 and COM3 on Port A ..............23
Connecting to COM1 and COM3 on Port B ..............25
Connecting multiple PLC/controllers serially using
daisy chaining ...........................................................26
Connecting one or more PLC/controllers via Ethernet
..................................................................................26
Troubleshooting .......................................................27
Chapter 4 – Creating a Sample Project ......................... 28
Starting EZwarePlus .....................................................28
To start Utility Manager and EZwarePlus: ..........28
Creating a Bargraph .....................................................28
To create Window 11: ........................................28
To create a Function Key: ...................................30
To create a Bar graph: ........................................33
To create a Set Word: .........................................36
To create a Bit Lamp: ..........................................41
To create a Set Bit: ..............................................43
Finishing Up .................................................................45
Saving your first project ......................................45
Compiling your first project ................................46
Simulating your first project ...............................46
Downloading your first project ...........................48
Chapter 5 – Simulator Mode ........................................ 50
The Simulation Screen .................................................50
Simulating the HMI is done in on-line or off-line
mode. .......................................................................50
To use off-line simulation mode from EZwarePlus:
..................................................................................51
To use off-line simulation mode from Utility
Manager ...................................................................51
To use on-line simulation mode from EZwarePlus
..................................................................................51
1010-1015, Rev. 03
- Operator Interface Terminals 1
- COPYRIGHT NOTICE 2
- WARRANTY 2
- IF SERVICE IS REQUIRED 2
- APPLICATIONS ASSISTANCE 2
- Table of Contents 5
- Chapter 1 – Introduction 9
- What You Need 10
- OIT/HMI Basics 11
- Graphics Object 12
- Windows 12
- List of Features 13
- Chapter 2 – HMI Local Setup 16
- Changing the System Settings 17
- Viewing System Information 22
- Adjustment) 25
- 1010-1015, Rev. 03 28
- HMI5000P/L/HD 34
- Troubleshooting 35
- Starting EZwarePlus 36
- Creating a Bargraph 36
- To create Window 11: 36
- To create a Function Key: 38
- To create a Bar graph: 41
- To create a Set Word: 44
- To create a Bit Lamp: 49
- To create a Set Bit: 51
- Finishing Up 53
- Saving your first project 53
- Compiling your first project 54
- Chapter 5 – Simulator Mode 58
- To use EasySimulator 60
- Chapter 6 – Using EZwarePlus 61
- Utility 63
- EasyPrinter 68
- Simulation Settings 75
- Pass-through mode 76
- EZwarePlus Features 79
- Managing Projects 95
- Display Options 97
- Basic Editing Commands 103
- Grouping Objects 108
- Layering Objects 108
- Nudging Objects 108
- Making Objects the Same Size 109
- System Parameter Settings 111
- Device tab settings: 112
- Model tab settings: 115
- General tab settings: 117
- System Setting tab settings: 119
- Security tab settings: 121
- Font tab settings: 124
- E-Mail tab settings: 127
- Recipes tab settings: 129
- Reboot HMI 131
- Save and Compile the Project 131
- Chapter 7 – Creating Windows 134
- Creating a New Window 135
- Window Settings 137
- Assigning Underlay Windows 138
- Deleting a Window 139
- Using Base Windows 140
- Using the PLC 141
- Using the Common Window 146
- System Message Windows 154
- Using the Tag Library 158
- Creating the Label Library 159
- Using the Label Library 162
- How to Create a Keypad 164
- Creating Bar Graphs 168
- Creating Meter Displays 171
- Displays 174
- History Data Display 180
- Using Alarm/Events 185
- Chapter 13 – Security 195
- General Mode 196
- Enhanced Security Mode 197
- Object Security 201
- Safety Control 202
- Interlock 202
- Auto logout 204
- Additional Security Features 204
- Project Protection 205
- Disable Upload Function 206
- XOB Password 207
- Decompiling Prohibited 208
- System Passwords 209
- User Accounts 214
- USB Security Key 216
- Chapter 15 – Recipes 222
- Chapter 16 – Operation Log 229
- View Settings 231
- General Tab 231
- Title Tab 233
- EasyDiagnoser 234
- Main Window 236
- Polling Packages 237
- Devices 238
- EasyWatch 239
- Reserved Local Bits 250
- Reserved Local Words 254
- 3 Year Warranty 264
- CUSTOMER 264
- SATISFACTION 264
Produits connexes et manuels pour Capteurs Watlow EZwarePlus Programming
Capteurs Watlow EZ-ZONE PM Manuel d'utilisateur
(111 pages)
(111 pages)
(134 pages)
(103 pages)
Capteurs Watlow EZ-ZONE RM Manuel d'utilisateur
(155 pages)
(155 pages)
Capteurs Watlow EZ-ZONE RMC Manuel d'utilisateur
(213 pages)
(213 pages)
Capteurs Watlow EZ-ZONE RMC Manuel d'utilisateur
(213 pages)
(213 pages)
KitchenAid YKEBC278 manuali
Manuali dei proprietari e guide per l'utente per Forno KitchenAid YKEBC278.
We fornisce 1 manuali pdf KitchenAid YKEBC278 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels